Towing Company in Senatobia, MS – Bo Denson Towing Inc.

Towing Company in Senatobia, MS - Bo Denson Towing Inc.



bodensontowinginc.com

Welcome to Bo Denson Towing Inc.!

Serving the Senatobia area since 1975, Bo Denson Towing Inc. handles lockouts, towing, recovery towing, jump starts, tire changes, roadside assistance as well as mobile truck and semi-truck repair. If you need a tow or roadside assistance, call now! We offer 24-hour emergency service and we tow all makes and models.

At Bo Denson Towing Inc., we make it a point to make a tough moment better with speedy service, friendly drivers and mechanics, and all-around great customer service. We are looking forward to assisting you with your towing, recovery and transportation needs.

Call Bo Denson Towing Inc. today for more information or to get assistance fast!

#Towing
roadside semi truck tire repair

How to Plug a Tire Using a Tire Repair Kit

How to Plug a Tire Using a Tire Repair Kit



How to Plug a Car Tire Puncture. A demonstration of how to use an automotive tire repair kit to make a repair to a hole in a tire caused by a nail or screw. A screw is removed and the tire is plugged. Leak testing & follow-up air pressure checks are discussed.

Tooluxe Tire Repair Kit:

Subscribe and visit me here:

My Amazon storefront:

Music:
Special THANK YOU to my friends at Epidemic Sound!

* We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites
semi tire repair

Paraplegic & F700 Dump Truck with Lucas Girling Brake system and Dayton Wheels Hyper speed version

Paraplegic & F700 Dump Truck with Lucas Girling Brake system and Dayton Wheels Hyper speed version



This is the Hyper drive version of this brake job, still talk on a couple key points but fly through on the work side of it.
This is how a paraplegic changes a rear wheel seal and cleans brakes on the rear axle, on an F 700 dump truck with the Lucas Girling brake system. First manor is jacking up the axle to the tires can be removed, typically it’s a good ides to use jack stands but I didn’t have that luxury on this set up. Once off the ground then need to cage the spring brake or the brake chamber to free up brakes, you might need to adjust brake adjusters or you may not (that depends on if drum has a lip and catches on shoes) remove the nuts that hold the wedges and the wheel in place, once loose then smack the wedges with a hammer until they brake free. Remove the nuts and wedges, remove outside tire, remove spacer ring, and remove inside tire. From this point remove the nuts for the axle shaft and the coned shaped alignment washers by smacking the shaft with a hammer and vibrating them out, then remove the axle shaft. Now remove the outer nut with 3 1/2 hub socket, lock ring, inner nut, and finally the outer bearing. I made a puller to remove the hub, once freed up pull hub and drum together and set on ground.
Now flip it up and drive out the wheel seal and inner bearing, clean and check bearing and race, lube bearing and reinstall. Next install the new seal, be sure to drive it in square and set it flush at the base of the hub. I use 80 grit sand paper and give the shoes and drums a new surface to provide greater braking, clean out all dust and set hub and drum back onto axle. Take care not to damage the new seal, (IMPORTANT be sure to add oil in the hub before outer bearing unless you have a fill port in hub) oil outer bearing and install into the hub. Install the inner nut and tighten to press hub back into place, run nut down tight while turning drum to seat bearings. Loosen outer nut and then snug back down to set the end play on the bearings, when set install lock ring (in most cases you will have to make a small adjustment to the inner nut to get the pin and lock ring to engage) then install the outer nut and tighten. Next clean the axle shaft and hub, install RTV silicone to the hub and shaft to prevent gear oil from leaking. Install alignment washers and torque nuts. Throw the inner tire, spacer, and outer tire back on, install wedges and try to keep them even gaped. When tightening Dayton wheels you need to place an object next to the tire so you can check the run out of the tires, if the tire wobbles then you adjust the wedges accordingly until tires run true. Adjust brakes and uncage the spring brake, set tires back down on the ground and fill the diff with fluid. Last thing is to pack the tools up and ask why you didn’t take it and have someone else work om it!!! Thanks for watching. Please LIKE, SUBSCRIBE,and/or COMMENT!!
semi truck air brake chamber replacement

Lester's Transmissions and Towing

Lester's Transmissions and Towing



Lester’s Transmissions and Towing provides light to heavy-duty towing and recovery, along with automobile and truck repair, lockout services, and long-distance hauling. Visit us on the web at www.LestersTransmissionAndTowing.com
tow semi truck repair

Conti MH20 – Continental Truck & Commercial Tyres – Kansas City Trailer Repair – By USTrailer.com

Conti MH20 - Continental Truck & Commercial Tyres

Check out US Trailer Rental

Capture





Check out US Trailer Rental

Capture



Continental solid tyres are best for tough applications and are extremely stable, puncture-resistant and maintenance-free.

Able to withstand even the heaviest load, the MH20 tyres, and the treaded MC20, have a greater load capacity on smaller dimensions.

The damage resistance and high mileage performance of the MH20, regardless of the road service, combined with the wear resistant rubber compound increases the life and reliability of the tyre making it a cost efficient solution

Find out more today by visiting

source


Check out US Trailer Rental

Capture