In this video, 1AAuto shows you how to replace a front engine mounted radiator fan clutch on an 80s GM Truck. This process is the same for many fan clutches that mount to the front of the water pump with 4 bolts.
1. Removing the Radiator Fan Clutch 0:59
2. Replacing the Radiator Fan Clutch 4:29
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
How to fix a leaking gas tank. Without removing the gas or tank.
One day I had little fuel in my car and decided to fill my tank.
But the surprise was that there was a hole in the tank.
As the price of a new and repair was very high I decided to repair it.
I researched the internet and found a J-B weld epoxy and decided to experiment.
Until the day of publication of this video I had no problems.
Detailed step by step instructions. (See disclaimer below)
Buy Fuel Primer Rebuild Kit HERE –
Truck used – 2004 GMC 2500 engine code 2 – 6.6L LLY Duramax
Duramax Repairs Playlist –
Duramax Fuel Filter Change –
I am not a licensed mechanic. Take my advice at your own discretion. To the best of my knowledge this video is accurate. I am in no way responsible for any occurrence resulting from following the instructions in this video.
This is a quick and easy way to check if your fuel pump is really gone or if its just a relay.Im not saying this is going to fix all fuel pump problems but its a great place to start before spending hundreds on someone putting in a new fuel pump for you or spending hours of labor and a few hundred on materials you may not need. AS ALWAYS ALL REPAIRS ARE AT YOUR OWN RISK I AM NOT TELLING YOU WHAT TO DO JUST GIVING YA A HINT AT WHAT MAY BE WRONG
Easily rethread a skateboard/longboard truck axle using a die.
Don’t buy new trucks when you can easily fix your skateboard truck axles.
Go to for more info.
For great prices on Longboard and Skateboard equipment we recommend
Fix Threads On Skateboard Longboard Truck Axle
Damaged skateboard truck axle threads are caused from hitting the axle on the ground. Sometimes the axle nut gets ruined when being removing from a damaged axle. So you’ll need to replace the nut when repairing the axle or the nut can ruin it again.
A die is a tool that every avid skateboarder should have in their tool box. Damaged threads are common and a die is the only tool that will fix an axle properly.
Tools You’ll Need:
5/16″ inch –24 Die with handle (24 means threads per inch, which is also labeled as “Fine”)
Where to get a Die:
You can purchase a die and handle at most hardware stores for around $10. AVOID a cheap set.
You can also purchase a skate tool with a die made by Reflex called the Utili-tool.
Steps for Rethreading A skateboard/Longboard Truck Axle:
1. Remove the nut from the axle, and take off your wheel.
If your nut won’t come off try using a flat head screwdriver to pry up the nut while you turn the nut. If your bearing is stuck to your axle or hanger hit it with a hammer.
2. Remove the die from the handle and place the die on the axle. It may be a lot easier to get the die on without the handle. Plus, as you turn the handle you can lift the handle off the die since the deck will be in the way as you turn. Remove the die from the handle by loosening the tiny pin on the side of the handle.
3. Before turning the handle with the die inside make sure the die is perfectly perpendicular or flat against the axle. If it’s not you can ruin the threads or destroy the threads completely. This takes a lot of force so you’ll know right away to avoid causing permanent damage.
4. You only need to go down as much as the axle is damaged, so it may only be a few turns.
5. Replace the axle nut with a new one. when taking the truck axle nut off the threads inside it typically get damaged. Your original nut can ruin your axle threads all over again if you put it back on.
If you have problems with your truck kingpin bolt and want to rethread it the correct size die is 3/8″ inch –24.
If you have any questions regarding skateboard equipment we are here to answer them completely.
In this video I show you a simple free way to get a few months to an extra year out of your old Air compressor with a free quick fix.
SUBSCRIBE NOW to Nthefastlane! ▶
Visit My Website NOW! 💻 Website:
Help Support My Channel:
Visit me at:
If an “NTHEFASTLANE” Video has helped you in anyway, please, consider giving by using “Patreon” to help support my channel. The videos take a lot of time and effort to create. Creating video takes a lot of quality time that could be spent doing a repair that pays a lot more. Over all it make things a lot more difficult to pay the bills!. CLICK HERE:
Due to factors beyond the control of NTHEFASTLANE, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. Nthefastlane assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. NTHEFASTLANE recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of NTHEFASTLANE , no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not NTHEFASTLANE .